Manjaro Printing

Printing

From Manjaro
Revision as of 16:48, 16 December 2012 by imported>Verityproductions

Overview

Note
All the necessary printer software will be pre-installed in the full version of Manjaro. However, if installing the NET-Edition, a guide on installing CUPS, printer drivers, and other appropriate software can be found in the Printing Enablement Guide.

If you find that you are unable to print, then it may be necessary to enable CUPS (previously an acronym for Common Unix Printing System). This is a popular open source printing system used in most Linux distributions due to its ease of use. As stated by Wikipedia:

'CUPS consists of a print spooler and scheduler, a filter system that converts the print data to a format that the printer will understand, and a backend system that sends this data to the print device. CUPS uses the Internet Printing Protocol (IPP) as the basis for managing print jobs and queues. '


Enabling CUPS

All commands listed below require that you first open your terminal.


To permanently enable CUPS, input the command:

sudo systemctl enable cups.service


Once enabled, to start using CUPS immediately without rebooting, input the command:

sudo sudo systemctl start cups.service


Otherwise, to temporarily enable CUPS for a single session, input the command:

sudo cupsd


Adding a Printer

Don't worry - there's no need to use the terminal here! In fact, assuming CUPS has been enabled (and started), upon connecting a printer, it should be automatically detected and configured for you to use. The process itself should take only about a minute. However, if the automatic detection and configuration doesn't seem to work, then your printer can be manually set up with relative ease. There are two methods to do so:

  • Webpage Interface: CUPS provides an webpage interface that will open in your default web browser to configure your printer. This interface also provides access to further information about CUPS, as well as on-line help.
  • Desktop Interface: A standard desktop wizard is also available, which should be instantly familiar to those who have configured a printer before, whether using Linux or another operating system such as windows.


CUPS Webpage Interface

CUPSweb.png


To access the webpage interface, select Manage Printing from your desktop menu. The interface will automatically open in your default web browser. Alternatively, you can also open your choice of web browser, and enter the following into the address bar:

http://localhost:631/



Tip
You can also just click the address provided above to access the CUPS web interface!



CUPS Desktop Interface Part 1: The Automatic Method

CUPS1.png


1. Add your printer. Ensuring that your printer is properly connected and switched on, select Print Settings from your desktop menu. Once the Print Settings window has opened, click + add to add a new printer.


CUPS2.png


2. Select your printer name. Once the New Printer window has opened, under the Select Device heading, find the name of your printer and click to highlight it. If your printer is listed more than once, check the description on the right to ensure your selection is not for another function, such as scanning or faxing.


3. Select your printer connection. Under the Connection heading, click to highlight your printer's connection method. As illustrated, this will usually always be 'USB'.


CUPS3.png


4. Install your printer driver. Once your printer name and connection have been highlighted, click the Forward button and CUPS will automatically search for the available drivers for it. In most instances, once the appropriate driver has been found it will be automatically installed, and the set-up process will have completed.

Otherwise, if the process did not succeed, it will be necessary to click the forward button again in order chose the appropriate driver yourself.


CUPS Desktop Interface Part 2: The Manual Method

CUPS4.png



Tip
CUPS will usually help you out by showing recommended choices for each step.

1. Select your printer make. If the Automatic method did not automatically find and install an appropriate driver for your printer, then clicking the forward button again will present the Chose Driver window. The first step is to select the make of your printer. As illustrated, as an HP printer is to be installed, the recommended choice of HP has been highlighted by clicking on it.

Once your make of printer has been highlighted, click the forward button to proceed to the next step.


CUPS5.png


2. Select your printer model. Under the left-heading models, select the specific model of your printer. As illustrated, as the printer model to be installed in this instance is a Model 2210, the recommended choice of PSC 2210 has been highlighted by clicking on it.


3. Select your printer driver. At last! Under the right-heading Drivers, select the appropriate driver for your printer. As illustrated, the recommended printer driver has been clicked to highlight it. It is advised that you also select whatever driver is recommended for you.

Once your printer model and driver have been highlighted, click the forward button to proceed to the next step.


CUPS6.png


4. Choose your printer name, description (optional), and location (optional). Unless you want to change something, it will not be necessary to make any amendments here.

If you are happy with the information provided - or have made the desired changes - click the Apply button to complete the process.


CUPS7.png


5. Configure your printer. Having clicked the Apply button in the previous step, your printer's properties will be displayed. By selecting the categories on the right-hand side, you can view information and amend your printer's settings if you wish. The standard settings will be fine for most people, so unless you have something specific in mind, there will be nothing you need to do.


6. Test your printer. Although optional, this step is highly recommended! Click the Print Test Page button to ensure that your printer is set up and working properly.



Tip
Your printer properties can be accessed - and changed - at any time by selecting the Print Settings option from your menu, and then double-clicking your printer's icon.

That's it! Now click the OK button to close the window and start using your printer.


Configuring an Installed Printer

To configure an installed printer at any time:

1. select the Print Settings option from your desktop menu, and

2. double-click the printer's icon.

The configuration window will appear. Select any of the categories on the left-hand side of the window to view the appropriate information and make any desired changes. Once complete, click the Apply and then OK buttons to confirm and save your changes, or click the Cancel button to close the window without making any changes.


Removing an Installed Printer

If for any reason you wish to remove a printer (e.g. to reinstall it), select the Print Settings option from your menu, right-click your printer's icon, and then select delete. You will need to confirm your decision to delete the printer, as well as enter your password to complete the task.


Disabling CUPS

If for any reason you wish to disable CUPS (e.g. in order to use an alternative printing system), open your terminal and enter the following command:

sudo systemctl disable cups.service


See Also

Cookies help us deliver our services. By using our services, you agree to our use of cookies.