Difference between revisions of "Worker - An Introduction"

Line 137:

fonts {

globalfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";

buttonfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";

leftfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";

rightfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";

textviewfont = "fixed";

}

xftfonts {

globalfont = "Sans-18";

buttonfont = "Sans-20";

leftfont = "Sans-24";

rightfont = "Sans-24";

textviewfont = "Sans-20";

}

By looking at the above you can see that it is the xfgfonts section that is where the large 18 -> 24 size fonts are, ~~sou~~ you just make all those numbers suitably smaller so you can use the Worker Configuration GUI to fine tune your imported settings to suit the new machine.

By looking at the above you can see that it is the '''xfgfonts''' section that is where the large 18 -> 24 size fonts are, so you just make all those numbers suitably smaller & change nothing else, then you can use the Worker Configuration GUI to fine tune your imported settings to suit the new machine.

When I import the setting to another machine, I first install Worker then I just copy my backup ~/.worker/config file into the same location on the new machine. It is the simplest most effective method as it totally replaces the original file.

@@ Line 137: / Line 137: @@
   fonts {
-	globalfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
+         globalfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
-	buttonfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
+         buttonfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
-	leftfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
+         leftfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
-	rightfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
+         rightfont = "-*-verdana-bold-r-normal-*-14-*-*-*-*-*-*-*";
-	textviewfont = "fixed";
+         textviewfont = "fixed";
   }
- xftfonts {
+         xftfonts {
-	globalfont = "Sans-18";
+         globalfont = "Sans-18";
-	buttonfont = "Sans-20";
+         buttonfont = "Sans-20";
-	leftfont = "Sans-24";
+         leftfont = "Sans-24";
-	rightfont = "Sans-24";
+         rightfont = "Sans-24";
-	textviewfont = "Sans-20";
+         textviewfont = "Sans-20";
   }
-By looking at the above you can see that it is the xfgfonts section that is where the large 18 -> 24 size fonts are, sou you just make all those numbers suitably smaller so you can use the Worker Configuration GUI to fine tune your imported settings to suit the new machine.
+By looking at the above you can see that it is the '''xfgfonts''' section that is where the large 18 -> 24 size fonts are, so you just make all those numbers suitably smaller  & change nothing else, then you can use the Worker Configuration GUI to fine tune your imported settings to suit the new machine.
+When I import the setting to another machine, I first install Worker then I just copy my backup ~/.worker/config file into the same location on the new machine. It is the simplest most effective method as it totally replaces the original file.
 <br clear="all"/>