Difference between revisions of "Preserve Manjaro Bootloader/en"

Boot up all other linux OS and at their terminals, do

Boot up all other linux OS and at their terminals, do

When installing a new linux OS, at their installer, always select "installing bootloader to partition". We can also choose not to install bootloader, but selecting 'to partition' (Manjaro calls this 'to system') is good enough and is preferable to have a bootloader installed at every OS.

When installing a new linux OS, at their installer, always select "installing bootloader to partition". We can also choose not to install bootloader, but selecting 'to partition' (Manjaro calls this 'to system') is good enough and is preferable to have a bootloader installed at every OS.

At any linux OS terminal, see output of

At any linux OS terminal, see output of

It will give an output like this:

It will give an output like this:

  BootCurrent: 0001

  BootCurrent: 0001

  Timeout: 1 seconds

  Timeout: 1 seconds

  Boot0005* Hard Drive

  Boot0005* Hard Drive

  Boot0008* Systemd Boot Manager

  Boot0008* Systemd Boot Manager

Make sure Manjaro bootorder is at the beginning as above: "BootOrder: 0001,0002,0004,0005,0008"

Make sure Manjaro bootorder is at the beginning as above: "BootOrder: 0001,0002,0004,0005,0008"

If it is not, reorder such that it is, like this:

If it is not, reorder such that it is, like this:

Whenever we install another OS, it will be at the top of that bootorder; and we will need to reorder such that Manjaro is again at the top. And we can do that at that install livecd media itself. If we forget, we can do it after installation at any OS. For UEFI, we can still select Manjaro to boot at boot-setup (one of F8 ~ F12).

Whenever we install another OS, it will be at the top of that bootorder; and we will need to reorder such that Manjaro is again at the top. And we can do that at that install livecd media itself. If we forget, we can do it after installation at any OS. For UEFI, we can still select Manjaro to boot at boot-setup (one of F8 ~ F12).

However in some situations (and reported in some topics here), it is not (possibly due to firmware issues). The above steps do not ensure that Manjaro bootorder will be booted up. In these cases, one extra command is required.

However in some situations (and reported in some topics here), it is not (possibly due to firmware issues). The above steps do not ensure that Manjaro bootorder will be booted up. In these cases, one extra command is required.

Or, if done at livecd (or another OS) and mounted / partition to /mnt and /boot/efi partition to /mnt/boot/efi

Or, if done at livecd (or another OS) and mounted / partition to /mnt and /boot/efi partition to /mnt/boot/efi

Copying /boot/efi/EFI/Manjaro/grubx64.efi instead of /boot/grub/x86_64-efi/core.efi can also accomplish the same thing because /boot/efi/EFI/Manjaro/grubx64.efi is itself a copy of /boot/grub/x86_64-efi/core.efi

Copying /boot/efi/EFI/Manjaro/grubx64.efi instead of /boot/grub/x86_64-efi/core.efi can also accomplish the same thing because /boot/efi/EFI/Manjaro/grubx64.efi is itself a copy of /boot/grub/x86_64-efi/core.efi

So doing this is also an alternative.

So doing this is also an alternative.

Doing this extra command where the extra command is not needed does not seem to harm the system.

Doing this extra command where the extra command is not needed does not seem to harm the system.

At the other OS grub 2 system, create a custom.cfg file

At the other OS grub 2 system, create a custom.cfg file

Some OS's like Suse, Fedora, Mageia uses directory in /boot/grub2 not /boot/grub, so do so accordingly.

Some OS's like Suse, Fedora, Mageia uses directory in /boot/grub2 not /boot/grub, so do so accordingly.

Then add the following in the newly created custom.cfg. No need to update-grub or change /etc/default/grub and will stand (persist) grub-installs or update-grubs. And of course persists to any new Manjaro kernel. Note this entry/entries will not be shown in their grub.cfg.

Then add the following in the newly created custom.cfg. No need to update-grub or change /etc/default/grub and will stand (persist) grub-installs or update-grubs. And of course persists to any new Manjaro kernel. Note this entry/entries will not be shown in their grub.cfg.

     insmod part_gpt

     insmod part_gpt

     part part_msdos

     part part_msdos

     configfile /boot/grub/grub.cfg

     configfile /boot/grub/grub.cfg

  }

  }

btrfs will need additional tweeks (rootflag=subvolume=@)

btrfs will need additional tweeks (rootflag=subvolume=@)

[[Category:Contents Page{{#translation:}}]]

[[Category:Contents Page{{#translation:}}]]