Difference between revisions of "Btrfs Maintenance"
(rotating disks) |
(Btrfs needs no maintenance Warning) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 8: | Line 8: | ||
== Btrfs needs no maintenance == | == Btrfs needs no maintenance == | ||
This even | |||
* You always keep 10% of your volume unallocated | This can even be true when: | ||
* You always keep 10% of your volume '''unallocated''' | |||
{{BoxWarning|free or unallocated|I'm not saying "free" because with btrfs, free means nothing. The value you need to pay most attention to is '''unallocated''' ! }} | |||
==== Every filesystem needs some maintenance ==== | ==== Every filesystem needs some maintenance ==== | ||
Some filesystems do an automatic chkfs at every XX. mount | Some filesystems do an automatic chkfs at every XX. mount. | ||
Others need the user to do a chkfs manually. On most you have to watch not to fill them to 100%. | Others need the user to do a chkfs manually. On most you have to watch not to fill them to 100%. Others reserve 5% for root. | ||
Some filesystems need to be defragmented. Others do not. | Some filesystems need to be defragmented. Others do not. | ||
| Line 37: | Line 38: | ||
btrfs will mount the subvolume read-write. | btrfs will mount the subvolume read-write. | ||
== Manual | == Manual Maintenance == | ||
From time to time it may be advisable to check the health of | From time to time it may be advisable to check the health of a btrfs volume. | ||
{{BoxInfo| | {{BoxInfo|Note| Btrfs is used to perform all maintenance on '''a normally running system'''. The volume can be fully used. Shutting down during such an action is also unproblematic. Btrfs will keep running the action after the next launch until it completes.}} | ||
=== | === Usage === | ||
Check if the '''unallocated''' space on your volume is ok. | |||
==== check unallocated space ==== | ==== check unallocated space ==== | ||
{{RootCmd|command=btrfs filesystem usage -h /}} | {{RootCmd|command=btrfs filesystem usage -h /}} | ||
The commonly used term "free" is meaningless to btrfs users. Even if you have 50% of your volume "free", you | {{BoxWarning|Pay special attention to '''unallocated''' !|The commonly used term "free" is meaningless to btrfs users. Even if you have 50% of your volume "free", you can run out of storage space. }} | ||
Try to | Try to leave '''at least 10%''' of your volume unallocated. If this got below 10%: | ||
* | * Expand the volume to double size (see: [[Btrfs]]) | ||
* | * Delete some unused data | ||
* | * Delete some old snapshots | ||
* | * Balance ([[Btrfs]]) | ||
==== | ==== Clean up unused snapshots ==== | ||
From time to time it is necessary to check if you have snapshots that you | From time to time it is necessary to check if you have snapshots that you no longer need but that are taking up valuable space on your volume. | ||
=== | === Balance your free disk space === | ||
If you have some | If you have some "free" space on your volume, but the unallocated space is below 10% (or close to 10%), you can help btrfs to rebalance some parts. | ||
{{RootCmd|command=btrfs balance start -musage=50 -dusage=50 /}} | {{RootCmd|command=btrfs balance start -musage=50 -dusage=50 /}} | ||
Btrfs looks for chunks that contain more than 50% free space. It will take 2 of them and then move everything into a new chunk. After that, | Btrfs looks for chunks that contain more than 50% free space. It will take 2 of them and then move everything into a new chunk. After that, a chunk is released. This continues until each chunk is at least 50% full. | ||
This will give you some unallocated(free) chunks that help btrfs **not** to get out of space. | This will give you some unallocated (free) chunks that help btrfs **not** to get out of space. | ||
If you have less than 20% unallocated space, please do the following: | If you have less than 20% unallocated space, please do the following: | ||
{{RootCmd|command=btrfs balance start -musage=75 -dusage=75 /}} | {{RootCmd|command=btrfs balance start -musage=75 -dusage=75 /}} | ||
Btrfs looks for chunks that are less than 75% full. | Btrfs looks for chunks that are less than 75% full. | ||
It will take 4 of them and then move everything into 3 new chunks. After that, | It will take 4 of them and then move everything into 3 new chunks. After that, a chunk can be released. This continues until each chunk is at least 75% full. | ||
If you still have less than 20% unallocated space, please do the following: | If you still have less than 20% unallocated space, please do the following: | ||
{{RootCmd|command=btrfs balance start -musage=90 -dusage=90 /}} | {{RootCmd|command=btrfs balance start -musage=90 -dusage=90 /}} | ||
=== scrub === | === scrub === | ||
Check if everything is ok with the checksums and the readability of your data. | Check if everything is ok with the checksums and the readability of your data. '''Only do this when in doubt'''. This may take a long time as btrfs has to read ALL the data. Btrfs only scans the portion of your volume that actually contains data. | ||
{{RootCmd|command=btrfs scrub start -Bd /}} | {{RootCmd|command=btrfs scrub start -Bd /}} | ||
{{BoxSuccess|Want to watch how btrfs works ?| | |||
{{UserCmd|command=pamac install procps-ng}}}} | |||
{{BoxSuccess|After that inside a separate terminal:| | |||
{{RootCmd|command=watch -n 60 btrfs filesystem usage -h / }}}} | |||
== special cases == | == special cases == | ||
There seem to be some cases where additional maintenance is needed. | There seem to be some cases where additional maintenance is needed. | ||
==== | ==== SSD ==== | ||
===== Read | Btrfs is optimal for SSDs due to its CoW nature | ||
This | |||
===== Read rate degradation (unconfirmed) ===== | |||
This isn't a problem with SSDs in general, it just seems to happen in a few rare cases. Updating the firmware should then solve the problem. | |||
One way to test the read speed with btrfs is to read out all the data (scrub). If your SSD seems to have this RRD issue, '''balancing''' will help so that all data is written to a new location. This can be done while the system is running! But please only '''once''' a year! | |||
{{RootCmd|command=btrfs balance start --full-balance /}} | {{RootCmd|command=btrfs balance start --full-balance /}} | ||
This will take a long time. You can | This will take a long time. You can shut down your PC at any time. Do not be surprised. The "balance" will restart after booting until done! | ||
If you want your data to rotate: | |||
{{RootCmd|command=btrfs balance start -dlimit=10 /}} | {{RootCmd|command=btrfs balance start -dlimit=10 /}} | ||
This | This rewrites 10 chunks at a time. This can be used weekly if you find it necessary. | ||
==== Rotating disks ==== | ==== Rotating disks ==== | ||
Latest revision as of 14:19, 29 January 2023
Btrfs Maintenance
Btrfs needs no maintenance
This can even be true when:
- You always keep 10% of your volume unallocated
Every filesystem needs some maintenance
Some filesystems do an automatic chkfs at every XX. mount. Others need the user to do a chkfs manually. On most you have to watch not to fill them to 100%. Others reserve 5% for root. Some filesystems need to be defragmented. Others do not.
Every filesystem has its own needs and tools !
Automatic maintenance
Btrfs does some maintenance automatically.
Is the Volume in a clean state
At mount btrfs tests wehter the volume is in a clean state.
power down
Most file systems are not prepared for a sudden loss of power. If the computer suddenly loses power, transactions may not be written or only partially written to the volume. File systems that use journaling can often recover after a power failure.
Btrfs attempts to clean the volume by removing the last (uncompleted) action. This can result in losing the last changes you made before turning off. But you get a clean file system that doesn't need to be repaired.
error
If btrfs encounters an unrecoverable error, such as a checksum mismatch, the filesystem will be mounted read-only. (When using RAID2, such errors are auto-repaired)
clean
btrfs will mount the subvolume read-write.
Manual Maintenance
From time to time it may be advisable to check the health of a btrfs volume.
Usage
Check if the unallocated space on your volume is ok.
check unallocated space
Try to leave at least 10% of your volume unallocated. If this got below 10%:
- Expand the volume to double size (see: Btrfs)
- Delete some unused data
- Delete some old snapshots
- Balance (Btrfs)
Clean up unused snapshots
From time to time it is necessary to check if you have snapshots that you no longer need but that are taking up valuable space on your volume.
Balance your free disk space
If you have some "free" space on your volume, but the unallocated space is below 10% (or close to 10%), you can help btrfs to rebalance some parts.
Btrfs looks for chunks that contain more than 50% free space. It will take 2 of them and then move everything into a new chunk. After that, a chunk is released. This continues until each chunk is at least 50% full.
This will give you some unallocated (free) chunks that help btrfs **not** to get out of space.
If you have less than 20% unallocated space, please do the following:
Btrfs looks for chunks that are less than 75% full. It will take 4 of them and then move everything into 3 new chunks. After that, a chunk can be released. This continues until each chunk is at least 75% full.
If you still have less than 20% unallocated space, please do the following:
scrub
Check if everything is ok with the checksums and the readability of your data. Only do this when in doubt. This may take a long time as btrfs has to read ALL the data. Btrfs only scans the portion of your volume that actually contains data.
special cases
There seem to be some cases where additional maintenance is needed.
SSD
Btrfs is optimal for SSDs due to its CoW nature
Read rate degradation (unconfirmed)
This isn't a problem with SSDs in general, it just seems to happen in a few rare cases. Updating the firmware should then solve the problem. One way to test the read speed with btrfs is to read out all the data (scrub). If your SSD seems to have this RRD issue, balancing will help so that all data is written to a new location. This can be done while the system is running! But please only once a year!
This will take a long time. You can shut down your PC at any time. Do not be surprised. The "balance" will restart after booting until done!
If you want your data to rotate:
This rewrites 10 chunks at a time. This can be used weekly if you find it necessary.
Rotating disks
On spinning disks, fragmentation can become an issue in some rare use cases. Then you can defragment your Btrfs volume.
Defragmentation (not recommended)
This is NOT the same as defragmentation in older Windows file systems. Btrfs does NOT require defragmentation as normal maintenance. Only do this if you can measure a huge read performance loss because a specific file/database is fragmented!
See Also
Btrfs Learn basics about btrfs