This page provides information on some of the filesystems commonly used in Manjaro. It also shows where and how they are used. Further information on these and other filesystems can be found in the ARCH Wiki.
A filesystem manages the space on a storage medium (hard disk, SSD ...). It makes this memory available to the operating system so that files can be saved and read again. Each of the following filesystems has advantages and disadvantages. They are mostly developed for a special purpose and are therefore used in a certain environment.
filesystems that are mostly used under Linux.
Note that many filesystem drivers are already included in the Linux kernel. You may not need anything else to mount, read, or write these filesystems. But there are packages with additional tools. You may need them to format, check, repair, modify, or optimize such filesystems. So if you regularly use a filesystem, it is a good idea to install the appropriate tools.
Ext2 → Ext3 → Ext4
Ext4 is the default filesystem in Manjaro at the moment. It is the evolution of the most used Linux filesystems (Ext3, Ext2) and promises improved design, better performance, reliability, and features over its predecessors.
If you are using Ext2 or Ext3, you can convert the partition to Ext4. Ext4 uses journaling, checksums and write barriers and is therefore more robust against damage.
Currently Ext4 is fully supported in Win10 and OsX. Support for ext4 has been built in since WSL is included in Win10 (2016).
In Manjaro, e2fsprogs is already installed
A modern Copy on Write filesystem for Linux aimed at implementing advanced features while also focusing on fault tolerance, repair and easy administration. Btrfs not only is a filesystem, but also is partly a volume manager, software-raid, backup-tool, and it is flash-friendly.
Development of Btrfs started in 2007. Since that time, Btrfs is a part of the Linux kernel and is under active development. The Btrfs code base is stable . However, new features are still under development. Its main features and benefits are:
- Snapshots which do not make a full copy of files
- RAID - support for software-based RAID 0, RAID 1, RAID 10
- Self-healing - checksums for data and metadata, automatic detection of silent data corruptions
ReiserFS → reiser4
ReiserFS was the first journaling filesystem to be included in the standard kernel. It was actively used by some distros some time ago, but is not currently widely used. Reiser4 is the successor to ReiserFS(3). However, Reiser4 seems not to be integrated in the kernel yet.
filesystems mostly used in windows
It is the most widely used filesystem on windows these days. It does exist in different versions, but unlike FAT32, all of them offer the following points:
- Large files> 4GB
- Long file names with UTF16 up to 255 characters
- Rights management, ACL
- Journaling of metadata
- Compression, encryption, ...
Currently there are some restrictions when using NTFS with Linux. If windows is suddenly switched off or goes into hibernating, the NTFS filesystem is left in a "dirty-state". When Windows starts again, NTFS is the first to be cleaned. This operation is currently not supported by the Linux driver. Then Linux shows the NTFS filesystem as read-only to be on the safe side.
filesystems under DOS and early windows on a lot of floppydisks and USB-sticks
FAT16 → FAT32 (+VFAT)
This is a traditional filesystem under DOS and early Windows versions. Even today it can be found on many floppy disks, USB sticks and hard drives. It is supported by all types of operating systems and is therefore often used to exchange files, to pass them on, or to keep them accessible to both operating systems in the case of dualboot.
Even with FAT32, this comes not without its disadvantages.
- no support for user rights or xattr
- severely restricted file names (8.3 or LFN for VFAT, no distinction between lowercase and uppercase)
- no files over 2GB (FAT16) 4GB (FAT32)
- no journaling
- not robust
Microsoft developed the exFAT (Extended File Allocation Table) in 2006 and optimized it for flash memories such as USB sticks and SD cards. It can store large files and large numbers of files, and it can manage very large partitions. It is supported by Linux, Windows, macOS and many other devices and is one of the most compatible filesystems. ExFAT is included in Linux 5.4 and higher.
- Flash friendly
- No support for user rights or xattr
- Files over 4 GB
- Checksums for metadata
- No journal
- Not robust
Filesystems mostly used in macOS
HFS → HFS+
Install from AUR
|btrfs||● btrfs-progs||▷ ExtFS, WinBtrfs||-||-|
|reiser3||● reiser4progs||▷ RFSTool||?||-|
▶ 5.15?? ntfs3
|exFAT||▶ 5.4 exfatprogs||●||?||?|
|HFS||○ hfsprogs (AUR)||?||●|
● = fully supported, additional tools to install ▶ = included since kernel x.x.x ○ = partially supported ▷ = possible via external tools ? = feel free to extend ;-)
|journaling||-||● ordered||● ordered||● full||▶ 2.6||●|
|checksum||-||-||◎ metadata||● full||●|
zstd ▶ 4.14/5.1
|TRIM possible||-||-||▶ 2.6.33||▶ 4.3|
|small repair||● fsck||● fsck||● fsck||● auto||reiserfsck|
|journal repair||● fsck||● fsck||● fsck||● auto 3.2|
|repair after power loss||-||?||● tune2fs, fsck||● auto, scrub|